Last week, we talked about making the same character but in miniature form, so this week, I figured he deserved to have a larger version as well. It’s actually a very simple design but I’ve always meant to do something more with it since there are only a few illustrations I ended up doing and something about the hood, cape, and lack of any distinguishing facial features has always been evocative.
These motocross figures came with the other ones I discussed last week. I couldn’t tell from the pictures, but they were quite differently constructed and much more difficult to disassemble. Luckily, the huge tolerances on the loose joints will make painting it easier, since I can’t get it apart to make sure the joint parts do not scrape on each other. I figured the overall wiggle factor of the figure (high) would work for a character that spends a lot of time gliding through the moonlight sky.
The face sculpts on these guys are hilarious!
Painted black …
The hood as been sculpted on …
At the time of this writing, I have sculpted the hood. I initially thought of sculpting of the face but instead just turned the head around so the back of the head is now the front. I think the only facial features I will paint on are eyes. After pairing it black with an airbrush, I moved the main joints around to see which areas the paint wore away from, then tried to Dremel those areas Dow. I think that is the best I will be able to do since the rest of the figure is held together with rivets I can’t easily remove.
This week, I wanted to continue seeing if the Aliexpress motocross action figure I found would work well as an articulated figure for both the Rocketeer and Logan from The Thirteenth Hour. I’ve been quite impressed by this humble, unbranded, inexpensive figure marketed (depending on the seller) as a motorcycle rider, soldier, or “worker.” I decided to keep the figure as intact as possible and just add epoxy clay to parts I wanted to modify since I tend to find sculpting easier than finagling with joints and sourcing parts, as the joints are much better than anything I could create from scratch. As mentioned, this figure I found really is quite versatile, and for Cliff, all that was needed was to add the chest bib, jodhpurs, and sleeve cuffs. Here he is after some sanding:
For Logan, I think all that will needed will be the front and back halves of his tunic, the scarf/hood neck piece, the belt as part of the pelvis, and perhaps a bit of volume to his (rather parachute-like) pants. I would like to make an Aurora as well, but sourcing female figures is more difficult. I may actually modify this male one to have a female torso (the strategy the 80s GI Joe 3.75″ toys used) since then I could keep the joints intact. The main challenge with Aurora will probably actually be her skirt if her legs are really mobile – I probably won’t be able to get away with the sculpted one I did for legs that could only move forwards and backwards – perhaps cloth?
In the meantime, I decided it was high time that the hunter from The Thirteenth Hour prequel, A Shadow in the Moonlight (read it free in the US!), needed his own figure. This one was made from two modified Hero Construx figures with the addition of some clay, black paint, a cape, bow, and quiver.
Lastly, I finished up the mini Rocketeer made in episode 389 (the sculpt along). Here he is solo and with a clear translucent buddy.
This week, I’m sharing a bit of a possible shortcut to making articulated custom action figures. I recently discovered a source of inexpensive GI Joe style figures (minus the pesky O-ring) that can be disassembled easily. I found these motorcross guys on the website/app Aliexpress. Bought one on a whim wondering if I could modify it. Turns out, it was quite easy!
Here’s the motorcross rider with a different set of legs I took from a figure from The Corps line. I wanted to see if they could be made to fit. With some modification, yes. Within seconds, I took out three screws and motorcross guy was in pieces!
Said modifcation referenced above is widening the joint space on the new leg to fit the bigger joint pegs on motorcross guy.
The neat thing about this style of legs (that GI Joe and its competitors used and now replicated with motorcross guy and his pals) is that a single screw holds it all together.
Next stop – adding clay to modify this body into a Rocketeer.
I’m curious to try this method to make a new wave of more articulated Rocketeer and Thirteenth Hour figures!
This week, I’m continuing projects from the last few episodes, painting the Rocketeer minifigure made during the sculpt-along episode as well as Rocketeer game piece.
Pictures of these figures after the first coat of paint. Once the paint fully dries, it will be time for another coat or two as well as the details, like the jacket buttons and helmet lenses. I also still have to paint the flames and smoke on the game piece figure.
I recently ordered a large figurine from the company Hero Forge, making it about as close to Logan from The Thirteenth Hour as I could. I was planning to sculpt a little onto the parts that I couldn’t make exactly the same and then cast the head for a custom Logan Hero Construx figures.
Here is the figure before …
And after. Once the clay is dry, still a fair amount of detail work needed …
The Thirteenth Hour Podcast #389 and Like a H90 and Like a Hood Ornament #47: Rocketeer Minifigure Resin Casting Updates and Making a Game Piece 2ood Ornament #46: Rocketeer Minifigure Sculpt-along
This week, I’m continuing a project started back in episode 384, making a little game piece of the Rocketeer. My progress on that project was forestalled due to a batch of bad silicone, and it took awhile to get a new batch. I ended up switching to a different line within the Smooth On catalog called Mold Star 16 (since I could find it), and it ended up working out great. To celebrate, I made little cup molds of all the pieces of the Rocketeer mini figure parts I made last time (arms, legs, torso, head) as well as finally making a mold of the Rocketeer board game piece I prepared for molding in episode 384.
I had fairly low expectations of how the game piece would turn out, but once I broke in the mold, it actually worked quite well despite the complexity and intricacy of the game piece.
I used one of the copies of the game piece to extract copies of the rocetpack and the helmet to modify the Hero Clix figure to the left (which I sanded down a bit to prepare it for the clay additions below – adding to the arms, making the chest bib with the buttons, and the jodhpurs). It will then need to be sanded down once cured to smooth it all out.
I attached the head using a pin to hold it in place (in addition to some superglue). I also angled the hed so it is looking a bit right, toward the upraised hand. It just felt more dynamic a pose. I just need to flesh out the smoke in back with some additional clay, sand things down, and then prime it for painting.
The first resin Rocketeer minifigure duplicate made from the figure we created last week. So far, I made four of them.
This week, we are trying something slightly new. I’m sculpting a custom Rocketeer minifigure from a base Flash figure (the DC superhero) with Aves epoxy clay in real time, and am doing my best to describe the process just through audio so you can do it at the same time if you so wish. If you want to follow along, here are the base materials:
Tools are pretty minimal, but it may help to have an X-acto knife, some tools or pieces of thin wood to shape the clay, some Vaseline to smooth over the clay, and a Dremel for cutting down parts of the figure (if you wish – I shaved down parts of the shoulder to make the figure less top heavy) and sanding the final product. Because of the size of the figure, it may also help to have a pair of reading glasses or a magnifying glass, though that is not required. Good lighting, though, is very helpful (a camping headlamp can really help).
We are going to be sculpting jodhpurs, adding the front bib of the Rocketeer’s jacket, adding cuffs to the sleeves, and making the helmet. The first four parts are basically adding pieces of clay and a bit of definition.
The next part is a bit more complex – adding clay to the head and then a piece of carboard to provide structure for the helmet’s fin. Adding clay to the outside of the cardboard piece will be stronger when it all dries than just trying to make the fin out of clay alone.
Here is the final result. After it all dries, I will do some final sanding to touch up a few spots. I will also be reworking the shoulder joints a bit so they fit better. I may also consider making molds of all the parts to be able to make resin casts of the pieces so make some duplicates.
I am using the same rocketpack I used for the Lego minifigures since the scale is about the same, though you could make your own (for the movie version – two torso sized bullet-shaped cylinders connected by a central rectangle). Next step after all this will be priming and painting.
If you made one of these along with this episode, send me a picture or tag me on social media! Would love to see wat you created.
This week, I’m discussing a discovery I made awhile back when considering how to showcase figures in The Thirteenth Hour DnD style campaigns we have been doing over on the Patreon via Discord. (I typically have a second camera set up to show an overhead view of the figures – so far, just during battles – this is an ongoing work in progress.) I thought it would be fun to include some miniatures but wasn’t sure how to find ones that would fit. Plus, I wanted them to be able to hold things in their hands and be somewhat customizable. Enter Mega Contrux minifigures.
Mega Bloks are a long time competitor of Lego that originally started as large scale bricks for young children, though just like Lego, they now have a number of highly complex, licensed properties more appropriate for the fingers and brains of older kids (and adults). Mega also has much more detailed, articulated, and realistically proportioned minifigures, and those are the ones I used for making The Thirteenth Hour minifigures. I started with a figure from their Assassin’s Creed line (I’m not sure who this guy is, but his costume has a number of similarities to the Imperial Ranger uniform – a tunic with large shoulders, grey pants, a hood, and a midsection piece that can be modified to make the triangular belt they wear).
Just like Lego minifigures, the Mega ones break apart for easy customization.
This skirt can be flipped around to make belts when painted.
From left to right – Aron, Blake, Lance, and Wander the wizard.
Wander was made very quickly with the same base figure with a tunic and wizard’s hat made of the same material. Added a bit of epoxy clay for hair and a beard. As you can see, there is a Lego baseplate in the background which I have used for positioning the figures during the game. One of the advantages of using these kinds of figures is that they have holes in their feet, making them easy to position. Mega figures also can use the full range of Lego hand held accessories (of which there are many), which makes it nice to customize them.
This week, I’m discussing packing for some of the upcoming toy projects I have been working on – 3.75″ Rocketeer action figures, the similarly sized Thirteenth Hour figures, and the Thirteenth Hour magnet dolls (the later two are basically part if the same project – the upcoming Once Upon a Dream LP launch. Each of these creative projects require some way to contain their respective parts, necessitating some kind of box with decorative coverart. While I can’t say it’s my favorite part of the whole process, I do think the packaging is of similar importance to the piece of art itself – the package is for protection, foremost, and makes it easier to ship, but it is also an accessory in its own right. It adds to the overall experience of the toy since it may add context, additional information or other pieces to collect, and a place to house the figure when it’s not being used.
Happy new year, and welcome to 2023! This first episode of the new year is all about time. Though time exists independent of all of us and will go on and on regardless of whether we exist in it or not, it is a finite resource for us living creatures. I think of an expression (which I might be paraphrasing) that my mother, who studied economics in college sometimes used (one I thought was humorous due to the extravagance of the words) – “diminishing returns of marginal utilities.” If I’m getting this correct, the “marginal utility” part describes the satisfaction that one experiences by consuming one unit of something. While economists are usually referring to “utility” in terms of as a product, I think the concept applies to some nonpurchasable items as well, including time. In some cases, the more time you have, the less you value it; yet when you have less, it becomes more and more precious. Gaining even a bit more would yield a net positive marginal utility. But none of us, regardless of our station in life, can get more of it. We all have however much time we are given, and none of us know how much.
There is a quote from the novel “The Sheltering Sky” by Paul Bowles that is inscribed on Brandon Lee’s tombstone (it came up in one of his last, if not the last interview he did prior to his death) that is particularly poignant and gets at this idea:
“Because we do not know when we will die, we get to think of life as an inexhaustible well. And yet everything happens only a certain number of times, and a very small number really. How many more times will you remember a certain afternoon of your childhood, an afternoon that is so deeply a part of your being that you cannot conceive of your life without it? Perhaps four, or five times more? Perhaps not even that. How many more times will you watch the full moon rise? Perhaps twenty. And yet it all seems limitless.”
Rocketeer creator Dave Stevens echoed similar sentiments when it came to his own work in ways I think many artists will be able to relate to. In the podcast, I include a segment from one of Dave’s journals read by Billy Campbell from the documentary Dave Stevens: Drawn to Perfection.
When I was initially writing The Thirteenth Hour as a teenager, I think I was trying to put these idea into words in my own way. I suppose I had a different view of time since I was younger, but looking at it decades later, I think that is one of the underlying messages of the book – taking life by the reins and making the most of it, that the world can what you make of it if you believe in your dreams and don’t sit passively by, letting time pass you by.
Interestingly, the Buddhists have a slightly different take on this since they believe in do-overs. Life, from a Buddhist perspective, is about suffering, and escaping this cycle of birth and rebirth is to finally find peace (a.k.a. nirvana). But for those of us still in the world, there are some interesting insights in this drawing below of the samsara (wheel of life). There is a segment of the wheel below (the one with the animals in it) that is called, not surprisingly, the animal realm. The Buddhist view of non-human animals is that they are not as evolved, not as intelligent (human-centric, I know) and so creatures born into this part of the samsara earned their lot in life though past negative karmic action. I don’t know if I agree with that, but I think you can also use aspects of this as an analogy for parts of human existence. When we are in the animal realm, we are focused on survival – just getting through the day. But when we get a breather and have better resources, we can enter into the higher realms where we have increasing ability to reflect on our situation and focus on more than day to day needs. Times like the new year sometimes give us cause to stop, pause, and reflect on where we want to go. So in this episode, I not only reflect on some of the positives of the past year and some goals for the one to come.
This week, my brother, Jeremy, rejoins the show to talk about the 80s movie, Legend in the second of a two part series (part one is here). As mentioned, depending on which part of the world you were in, it had different release dates (1985 in Europe, 1986 in the US) and different soundtracks and cuts, making for different viewing experiences. In this podcast, we focused on the 1986 US theatrical release with a soundtrack by Tangerine Dream and the 2002 director’s cut (more similar to the original 1985 European release) with the soundtrack done by Jerry Goldsmith.
When I was a kid watching the US release, I wasn’t really a fan of the ending song (“Loved by the Sun”), since I just wanted to listen to the backing melody (which is mostly synth and is the “Unicorn Theme” refrain) but watching it this time, I was struck by how this ending scene really caps off the whole movie. It’s basically a music video inside a film that’s 70% music video already (speaking for the US release), and what was running through my head was, “Now that’s how you end a movie! (especially an 80s movie).” While the director’s cut version is probably cinematically the better ending and makes a bit more sense (well, sort of), I couldn’t help wishing for the emotional swells of the vocals, keyboards, and synthesizers of the Tangerine Dream / US version. Check it out:
Jeremy had much the same thought. It was really nice to be able to share this little slice of the 80s with my brother, since he was not really old enough to get into it when I was into the film. Check out Jeremy‘s work over at Pixel Grotto, CBR.com, and Classic Batman Panels on IG. You can support his work on Ko-fi and get access to in-depth, exclusive Batman content here. If you are of the DnD persuasion, his articles on DnD Beyond may be right up your alley. Thanks, Jeremy, for coming on the show! Look for more in part 2 next week!
This week, my brother, Jeremy, rejoins the show to talk about the 80s movie, Legend. Depending on which part of the world you were in , it had different release dates (1985 in Europe, 1986 in the US) and different soundtracks and cuts, making for different viewing experiences. In this podcast, we focused on the 1986 US theatrical release with a soundtrack by Tangerine Dream and the 2002 director’s cut (more similar to the original 1985 European release) with the soundtrack done by Jerry Goldsmith.
Watching this film again for the first time since I was a teenager, I was struck by how much I liked the Tangerine Dream score in the US release, something I really noticed when watching the director’s cut version of the film. Before I was able to find the soundtrack, I recall trying to tape record parts of the soundtrack off the TV as a kid. Unfortunately, as was often the case, not all parts of the score were included on the official release. For example, this scene has a variation of “The Unicorn Theme” that was on the official soundtrack, if I recall. Listening to those home-made recordings through the years helped provide inspiration for what would later become the sound behind The Thirteenth Hour soundtrack.
It was really nice to be able to share this little slice of the 80s with my brother, since he was not really old enough to get into it when I was into the film. Check out Jeremy‘s work over at Pixel Grotto, CBR.com, and Classic Batman Panels on IG. You can support his work on Ko-fi and get access to in-depth, exclusive Batman content here. If you are of the DnD persuasion, his articles on DnD Beyond may be right up your alley. Thanks, Jeremy, for coming on the show! Look for more in part 2 next week!
This week, I’ve got a few quick updates and will be digging into the second set of questions that came in. I really appreciate all the thoughtful questions!
Before we begin, I have finally finished the Lego Rocketeer including their boxes. Now just need to list them and get them ready for auction for two charity organizations in Dave Stevens’ name.
1) What was it about films like The Neverending Story that resonated with you as a child and served as fuel for the style of ’80s fantasy that The Thirteenth Hour represents? In your mind, what do you think is stylistically different about ’80s fantasy films as opposed to the stuff that came after? (like The Lord of the Rings movies or modern day shows like The Witcher).
2) The Thirteenth Hour straddles a lot of genres and defies classification – you could call it a fantasy/young adult book, but that doesn’t quite hit the mark. What are some of the restrictions and quirks of these genres that bothered you as a kid and still bother you as an adult? (i.e.: the tendency for fantasy series to be long multi-book affairs that get a little drunk on their own worldbuilding and politics; the fact that most YA books have to fit within the mold established by Harry Potter or The Hunger Games to survive)
3) Did you ever envision The Thirteenth Hour as a comic? In a perfect world, what would a comic adaptation of the story look like in your eyes? Would you go for a long running series that expands on the mythology that you wrote, or maybe a big one-shot a la Dave Steven’s Rocketeer work that’s self-contained?
Check out Jeremy‘s work over at Pixel Grotto, CBR.com, and Classic Batman Panels on IG. You can support his work on Ko-fi and get access to in-depth, exclusive Batman content here. If you are of the DnD persuasion, his articles on DnD Beyond may be right up your alley. Thanks, Jeremy, for coming on the show!
These first five comes from frequent show guest Adam from @mom_gave_them_away, who was just on the show for episodes 340–341 on Rambo/First Blood.
4.) Favorite Gene Wilder role, not necessarily favorite movie?
5.) Favorite toy line as a kid?
6.) Within that favorite toy line, what’s your favorite figure?
7.) Can you nail down your favorite year of the 80s?
8.) Did you take piano lessons, and if so, do you remember your first lesson?
Find more of Adam’s work on the interwebs at ACtoydesign and his shop of original resin toys. He does a number of podcasts as well – I Have Spoken (a Star Wars podcast), Death by Podcast (a vintage horror podcast), and You like Toys (a Patreon exclusive podcast about toys and nostalgia).
Two of my favorite GI Joe figures – Lady Jaye and Snake Eyes from the GI Joe 80s cartoon.
I don’t a lot of the toys from my youth currently with me, but have found a few in later years. The little blue Prius from Japan is there representing Micro Machines and the Japanese import that was my first GoBot. The blue robot is a GoBot that was my favorite as a kid, and the Air Raider pilot (which was one of the ones I had as kid), represents all the smaller size figures I liked playing with as a child.
Thanks, everyone, for your contributions! It was a good time. We’ll do it again next month (for the episode to be released on 3/28/22). If you have questions, feel free to email me them at writejoshuablum@gmail.com.
1.) What’s your favorite 80s toy line of all time?
2.) What’s your favorite contemporary toy line of all time?
3.) If you could change one thing about The Rocketeer movie, what would it be?
4.) If there was a new Rocketeer movie, who would you like to see in the cast? Excluding the obvious choice of The Rock for the lead role.
5.) How many licks does it take to get to the center of a Tootsie Pop?
Find more of Adam’s work on the interwebs at ACtoydesign and his shop of original resin toys. He does a number of podcasts as well – I Have Spoken (a Star Wars podcast), Death by Podcast (a vintage horror podcast), and You like Toys (a Patreon exclusive podcast about toys and nostalgia).
6.) In a perfect world, if you had to pick just one, would you rather see The Thirteenth Hour visualized as a big budget movie akin to the 80s flicks that inspired you, a long-running cartoon series with one of those badass intros with dudes singing, or a retro video game like the one you tried to make way back in the day?
7.) I know that The Thirteenth Hour Book 2 has been on hiatus for a bit; has the general story changed at all due to side projects you’ve been engaged in? On that note, has the trajectory of characters like Logan, Aurora and the Wayfarer changed at all after everything that you’ve experienced the last two years as a dad raising kids in this crazy new Covid world we live in?
8.) Now that you’re a fully fledged custom toymaker, are there any other projects you want to embark upon with the characters from the book? Making Thirteenth Hour dioramas? The World of The Thirteenth Hour Guide Book? A new short story?
Check out Jeremy‘s work over at Pixel Grotto, CBR.com, and Classic Batman Panels on IG. You can support his work on Ko-fi and get access to in-depth, exclusive Batman content here. If you are of the DnD persuasion, his articles on DnD Beyond may be right up your alley. Thanks, Jeremy, for coming on the show!
Wrapping us up for the first Thirteenth Hour podcast Q & A is one of my favorite people in the world, Doug Bernon:
9.) If Howard and Beverly had a child, what do you think their kid would look and be like?
10.) How do you think Logan and Aurora would have handled a pandemic?
11.) Cliff Secord’s helmet is already pretty magnificent. If you were designing one for yourself today, what would it look like?
12.) What role did the movie The Rocketeer play in your life as a kid? Is that the backstory for Logan and Aurora and The Thirteenth Hour?
Thanks, everyone, for your contributions! It was a blast. We’ll do it again next month (for the episode to be released on 2/28/22). If you have questions, feel free to email me them at writejoshuablum@gmail.com.
This week, my brother, Jeremy, rejoins the show to talk about the 1985 Disney film, The Black Cauldron. The film is loosely based on the first two books in the Chronicles of Prydain series by Lloyd Alexander, a series I was sort of introduced to as a kid when I bought The Black Cauldron book in a school book fair since it had the cover of the movie, like this one:
The film poster usage for the cover of the novel is a bit misleading since the majority of the plot to the film is actually from the first book in the series, The Book of Three, which I was unaware of at the time. So, it’s not surprising it didn’t make much sense. However, we did have this Scholastic comic adaptation of the film which we found at a yard sale and read many times in childhood:
You can find copies on eBay periodically (click on the picture above to search):
Here’s the theatrical trailer and some screencaps:
The film had to be cut for length and content. Here is the first in a series of videos that has deleted scenes from the film:
Check out Jeremy‘s work over at Pixel Grotto, CBR.com, and Classic Batman Panels on IG. You can support his work on Ko-fi and get access to in-depth, exclusive Batman content here. If you are of the DnD persuasion, his articles on DnD Beyond may be right up your alley. Thanks, Jeremy, for coming on the show!
The Thirteenth Hour Podcast #336 and Like a Hood Ornament #42: Toymaking Updates, Dave Stevens Fundraising Update, Rocketeer Cards, and Working on the Backing Tracking of a New Song
In the first part of this show, I share a bit about a new song I’ve been working on for the upcoming Thirteenth Hour soundtrack LP, Once Upon a Dream. It’s called “No Hero.” I’m currently working on cleaning up the keyboard riff in the background since I’m old school and have to learn to play everything first before I can record it. One of these days, I’m going to have to go digital!
This past week, I’ve been working on putting the Thirteenth Hour action figures together. So far, here’s what they look like:
Logan …
Aurora …
Logan and Aurora …
I still have a few to fix / assemble. The ones in the center right are the original prototypes that I made the molds from, and I think I’ll go ahead and paint them as well also. Here are all the pieces and figures along with clear coated parts from the Lego minifigure Rocketeers I’ve been working on. These pieces, when done, will be auctioned off, with all funds collected donated to The Hairy Cell Leukemia Foundation (the complications of which took Dave Stevens from us) and Hero Initiative, which supports comic book artists.
Speaking of the Rocketeer, my brother gave me some vintage Rocketeer cards recently, which I’ve been slowly opening up. Here’s the next batch:
On the back, there is an ad for this souvenir magazine …
Inside, coincidentally, there’s an ad for the cards:
I recently discovered that the game Microsoft Flight Simulator X has a skin for the Gee Bee that is the same as the NR77V Gee Bee highlighted in the film (the one that crashes in the first few minutes of the film), which is the one that Dave Stevens showed in the comics (itself modeled after the City of Springfield model that crashed in the early 30s … though presumably, Cliff and Peevy found the remains and built it into the Gee Bee that was used the comics and the film). Nonetheless, check out these graphics! I know nothing about this sort of thing but next time this baby goes on sale …
Lastly, if you have questions for the show, 1/31/22 will have a listener Q and A segment. Thanks to all who submitted questions already! Get your questions in by 1/24/22 for inclusion in this month’s show! Email or anywhere on social is fine.
Thanks for listening!
∞∞∞∞∞∞∞∞
This winter, if you’re looking for an adult of child mask, check out Thirteenth Hour mask combo package on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812) which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
1.) the last episode of the month for the next few months will have a Q and A segment. Submit your questions via email or on social media (or if on Patreon, via messaging me there or commenting on the most recent post) to be a part of the show. It doesn’t necessarily have to be Thirteenth Hour or 80s related – anything you like or think would be interesting to discuss. Have fun with it!
2.) A few pics of the Lego Rocketeer minifigures I’ve been working on. They’re about 95% done. Just some touch ups needed then will begin work on the packaging.
3.) A picture of the current state of The Thirteenth Hour action figures. Just a few paint touch ups there, also, and then will start assembling the figures.
4.) Speaking of figures, I was thinking I’ve used this little bookshelf to take some pictures before, but I thought I’d use it more since it has a lot of my influences in book form!
5.) Introducing my kids to resin over the past few weeks has been entertaining (and messy). We’re making keychains here with a combo of Thirteenth Hour illustrations, Batman 1989 pictures, and Rocketeer stills. The kit we received came with these little molds perfect for making keychain and charm pendants (and just right for small fingers).
Protect yourself and others with the Thirteenth Hour mask combo package on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812), which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
In this episode, I’m reflecting back on the last year and planning for next. 2021 was a good year for the show (despite being a difficult year globally). I’m going to focus more this year on planning out episodes (including the more intentional scheduling of guests) to make it all a bit more systematic and organized than it has been in the past (which, up up until ow, was basically just an extension of whatever I was doing creatively at the time).
I’d also like to engage my listener base more, so if you have any suggestions, questions, comments, or requests for the show, please let me know! I’m going to try an experiment for a few months, making the last show of the month (1/31/22 in this month’s case to have a Q and A segment). More to come in the coming weeks. Listeners can also leave messages via voice on the main website (found on on the audio –> Thirteenth Hour podcast section):
A few updates on a few creative projects I’ve been wrapping up:
These were some resin bookmarks I made with my kids – their first introduction to resin art and mica powder:
A few pictures on the Lego Rocketeer figures I’ve been slowing working on. The packs are almost done; just wrapping up some details on the painting.
The figures will probably look something like this (an early draft):
Speaking of painting, the Kenner style Thirteenth Hour figures are almost done. Some heads of Aurora and Logan:
What Aurora will probably look like when done (she is in her outfit from the part of the book where she fights a dragon):
I also added little magnets to Logan’s boots to allow him to easily connect to Lightning, his hoverboard (which will be his accessory).
Wishing you the best as you begin a new year!
∞∞∞∞∞∞∞∞
Protect yourself and others with the Thirteenth Hour mask combo package on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812), which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
This is the last show of 2021! We’re finishing up the year with a few toymaking updates and finishing the reading of the Howard the Duck novelization.
If you celebrate Christmas, hope y’all had a good day. We tend to follow the Latin American tradition of extending Xmas to at least Three Kings’ Day in January since, with young children, it seems to work out best to not give ALL the presents on one day. And it make it a bit more relaxed. Speaking of the holidays, check out this cookie my brother, Jeremy, decorated showing a soaring Logan. There’s even an infinity sign lest yon man soaring over and through lofty peaks be mistaken for a mere snowboarder.
Speaking of Logan, about a year ago, I made my first real custom action figure – a fairly well articulated Logan from The Thirteenth Hour from an old GI Joe and the head of a character from Treasure Planet (I think).
This year, I’m about 80 percent done a similar, but in some ways more complex project – casting and making a number of copies of Logan and Aurora in Kenner-style 5 points of articulation form. The fine detail and touch up work is still yet to be done, but even so, it’s a simpler look with less moving parts. The simplicity allowed me to think about being able to cast all the parts and attempt to piece them together.
I still have two more separate figures to make as well as accessories and packing to figure out but will discuss more next week when discussing 2022 goals.
One goal I had this fall was to read a longer movie novelization on the show (I read a movie novelization of Spacecamp before, but it was pretty short). I was wondering if a 200 page book would drag. But done in little bits, it was fun to do, especially this one. After 19 episodes, reading roughly a chapter a session, we have finished reading the Howard the Duck movie novelization. It was quite an enjoyable experience, as I’ve mentioned before. In some ways, similar to the comic – part satire, part social commentary – as well as a healthy dose of existential angst exhibited by Howard almost making it part philosophical treatise – clearly, this Duck is more than meets the eye.
A few excerpts I liked:
And (spoilers ahead), you can’t beat this ending:
It’s been a nice activity to complete while working on the Beverly figurines.
Next week, the first episode of 2022!
∞∞∞∞∞∞∞∞
Protect yourself and others with the Thirteenth Hour mask combo package on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812), which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
The Thirteenth Hour Podcast #332 and Like a Hood Ornament #41: Toymaking Updates, the Christmas Rocketeer Episode (20), Rocketeer Unboxings, and Reading the Howard the Duck Movie Novelization Part 18
This week, we’re getting ready for the holidays by opening some presents my brother sent, watching the Rocketeer Christmas episode, discussing a few toymaking updates, and, of course, reading the next section of the Howard the Duck novelization.
As far as updates go, I’ve been sanding and painting, then sanding and painting some more. I’ve got the parts laid out for each figure and have been painting parts of them piece by piece.
This is a preliminary idea of what Logan will look like. Not all the colors have been painted in, obviously, but that will be the fun part – when all is painted and it’s ready to glue it all together.
Speaking of toys, my brother, Jeremy, who was last on for the Red Sonja episode, sent some Rocketeer gear, and I thought it might be fun to open it up on the show:
Then, we watch the Rocketeer cartoon Christmas Star episode. A few screenshots:
Now, check out the Hughesville Mayor’s Rocketeer sweater!
And check out these ornaments! Disney, take note!
Speaking of which, if you’re looking for a holiday gift, please consider checking out the Thirteenth Hour mask combo package on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812), which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
Lastly, we are also reading the next section of the Howard the Duck from the movie novelization. We are almost done! Only two more chapters to go. This past one has some humorous mid 80s satire/commentary on politics of the day (Ronald Regan economics and priorities, the Cold War, etc).
Next week, we finish Howard! Have a good holiday, everyone!
This week, we’re discussing a few toymaking updates, reading the next section of the Howard the Duck novelization, and thanking some people!
Last week, my daughter and I tried our hand at making a resin bookmark – it worked (kind of), though one half of the resin still is a bit tacky. I’ve been letting it sit in the garage, since day by day, it get less and less sticky, and it can do its stinky off-gassing there! I probably didn’t mix it thoroughly enough. However, in the meantime, another kind of resin came in the mail, and this kind is a lot easier to use (plus, it’s odorless). So we’ve tried again, with better results. This batch also came with a bunch of little jewelry and charm molds, which was pretty sweet (since there is always extra resin left over after you’ve poured what you intended to).
Here are all the different Thirteenth Hour action figures primed and ready for painting. Same with the Beverly Switzler figures. Painting is the part I like least, but I think that once I get started, it will go fine. I’m going to do these all assembly line style – painting all the arms, the legs, the shoes, etc. rather than each figure head to toe.
One other thing about priming is that it helps bring out the details when the resin is translucent. Compare these two Rocketeer packs – the primed one on the left, the unprimed one on the right.
Now, some thank yous. Thanks to Colin from I Used to Like this One for leaving a review on Apple Podcasts. If you haven’t checked out their show, please do so; Colin and Shawn cover a lot of the same kinds of films I talk about on here, they do good work, and I’ve enjoyed getting to know them over the years. You can listen on their website or on most of the major podcasting platforms. If you like what they do, consider supporting them on Patreon and become a producer of their show.
Another show that you may want to check out, this time a martial arts one, is First Cup with Jeremy, the founder of Whistlekick. Jeremy and I have worked together for a number of episodes for his main show, Martial Arts Radio, but this little morning show is one I only recently discovered. I really like the community that Jeremy and the other folks at Whistlekick have worked to create – one based on curiosity, focusing on the positive, open mindedness, and the sharing of information. Have martial arts questions or ones that might make for interesting discussion? If you join the Facebook group, you can leave a question for the show!
Jeremy recently modeled one of The Thirteenth Hour masks and gave the pod a shoutout. Glad it fits well and hope it helps this winter!
Speaking of which, if you’re looking for a holiday gift, please consider checking out the Thirteenth Hour mask combo package on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812), which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
Lastly, we are also reading the next section of the Howard the Duck from the movie novelization. This part of the novel has some really great writing. The author really beefed up what would have been a pretty thin novel with some humorous bits that elevate the usual pot-boiler status of these kind of books to something actually unique and fun that can stand firmly on its own, even if you haven’t seen the movie.
And in this section, the word “chowderhead” is mentioned (Rocketeer reference! Though, to be fair, Howard the Duck predated The Rocketeer by 5 years)
This week, we’re discussing a few toymaking updates, reading the next section of the Howard the Duck novelization, and talking about a new resin side project.
My daughter recently got interested in making resin bookmarks as gifts, so after making an initial mold, we made a trial bookmark with Alumilite resin. I don’t know if that’s the best one to use, since I find it overall difficult to work with, but it’s what I had and does dry hard and clear, which I think should work.
Alumlite is messy, viscous to use, and smelly, so we did this outside and went though at least 4 pairs of gloves. This is what we ended up with, so hope it cures! I did order some more resin that is often used by jewelry makers, that will hopefully be a bit easier to work with, so if this is a fail, we’ll try again. I think it’ll be fun it we can do it!
It’s tedious, but I’ve been making some slow progress on the Lego Rocketeer figures! The Cirrus X-3 packs now have attachments to go over the Lego minifigure neck peg (instead of magnets, like I originally thought). They are now primed and ready for silver paint. I have to cast a few more, but my goal is to make at least six minifigures. There are always a few that are collateral damage, so to speak, in the creation process (parts get broken, something doesn’t go as planned, etc).
If you’re looking for a holiday gift, please consider checking out the Thirteenth Hour mask combo package I recently put on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812), which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
Lastly, we are also reading the next section of the Howard the Duck from the movie novelization. This part of the novel has some interesting commentary on 80s attitudes (I’m guessing, added by the author, since it’s not really part of the movie). Here’s the section in the film (the part with the ultralight plan / car chase):
We’re just a few chapter away from finishing the novelization!
The Thirteenth Hour Podcast #329: Toymaking Updates, Aurora Inspiration -“Saving the Best for Last” by Daniel Horne, and Reading the Howard the Duck Movie Novelization Part 15
This week, we’re discussing a few toymaking updates, discussing one of the inspirations for one of Aurora’s outfits from The Thirteenth Hour, and reading the next section of the Howard the Duck novelization.
As I was preparing the first run of Thirteenth Hour action figures, I was reminded of where one of Aurora’s outfits came from. Back when I was a kid, you’d occasionally see fantasy art used in advertisements for video games and TSR Dungeons and Dragons material. This was one that I think was used in an ad in this copy of a tattered DnD magazine I think that was called Dragon. I’m not even sure it was credited, so I didn’t know the name of the painter or the painting for decades. But I loved the painting – the tension, the imagery, the fact that it tells so much in just one picture. Eventually, I somehow learned the name of the painting (I think by eventually figuring out who painted it), and learned it was done by Daniel Horne, and the name of the piece is “Saving the Best for Last.” The title, too is perfect (referring to the archer’s last arrow. I can literally feel myself tensing up internally seeing the threat looming up in front of the archer and the fact she has no more visible armament left). Here is the transcript of an interview I found with Daniel Horne back in 2011.
And if you like this picture, you can buy a copy of your own on the artist’s website (just like I did).
I recall sketching the hell out of this picture when I was a teenager, trying to capture the dynamic nature of the story depicted in the painting. I was inspired by the setting, her outfit, her bow, the big hair (it was 1987, after all), the “oh, snap” expression on the archer and wanted to pay homage to this painting and how much it meant to me in The Thirteenth Hour, just like all those other 80s influences I’ve talked about ad nauseum on this podcast and website. This character in Daniel Horne’s painting is probably the only other visual inspiration I had for Aurora other than Beverly Switzler’s hair in Howard the Duck. Even before I had written this part of The Thirteenth Hour, I had already created the scene and background for it in my mind and sketched out an early draft of the picture that would later become the one that would show up in the book below:
The same outfit showed up in the magnet dolls I made about a year ago (I still have to figure out what to do with these; I think some will come with a future Thirteenth Hour special edition album).
This was the first custom action figure I attempted – a tiny rendition of Aurora in her archer’s garb, the same one in the picture with the dragon above and, of course, the one inspired by the archer’s outfit in “Saving the Best for Last.”
And here is the Kenner-style 5 POA versions I’m in the process of painting. The parts are primed so far, so it’s just sanding, painting, repainting, and the final process of fitting the pieces together.
On the same store, you can also find the Thirteenth Hour mask combo package I recently put on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812), which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
This week, my brother, Jeremy, rejoins the show to talk about movie we watched a fair amount as a kid, 1985’s Red Sonja. Neither of us had seen it in decades and we honestly weren’t expecting much, but I asked Jeremy if he’d want to join me in rewatching it given all the experience he’s had the last few years with tabletop role playing games like Dungeons and Dragons. From what I had recalled, it seemed like an example of those games in live action, and I was curious to see what he thought. Suffice to say, Jeremy did a deep dive and more than delivered, which you can hear if you check out the episode. I had always operated under the assumption that 1986’s Howard the Duck was the first real Marvel comic book movie, but you could make a case for Red Sonja, which was under license by Marvel at the time, though there’s no mention of it in the credits from what I recall. Click on the picture below to watch:
If watching the whole film is not your bag, check out this 8 min compilation of some great lines plus the trailer. You’ll get the basic gist of the film and perhaps learn a thing or two, like why it’s important to not grip your hilt too tight (important life skill courtesy of Red Sonja that is generalizable beyond sword play, though I’m not exactly sure how).
Check out Jeremy‘s work over at Pixel Grotto, CBR.com, and Classic Batman Panels on IG. You can support his work on Ko-fi and get access to in-depth, exclusive Batman content here. If you are of the DnD persuasion, his articles on DnD Beyond may be right up your alley.
In toymaking news, I’ve been working on all these Beverlys! There is also a connection to our 1985 film above. A year after, we would, of course, see the film version of Beverly Switzler, another lead heroine, but one of a considerably less violent nature, the one depicted in the figurine above. Her costume in the film was equally impractical as Red Sonja’s but a lot less revealing than that of Red Sonja’s. There’s another connection, though. The very first issue of Howard the Duck featured a vaguely Red Sonja like character (it’s Beverly, though it’s presented kind of as a dream) in a parody of a Conan / DnD story. There’s even an appearance of everyone’s favorite friendly neighborhood webslinger for some off-the-wall reason (the original comics were pretty bonkers).
This week, we’re discussing a few toymaking updates and reading the next section of the Howard the Duck novelization. Some toymaking stuff first:
I recently finished the resin hoverboard for the mini Logan I made awhile back. Lightning, Logan’s magical hoverboard, has this shiny aqua console in front that I wanted to make out of resin but wasn’t sure how to do. I eventually got a passable result with Alumilite resin with blue mica powder mixed in. After a fair amount of fiddling and polishing, then painting, repainting, etc Lightning came out all right. I’d like to do something similar for the 5 POA Kenner style figures I’m making, since that’s Logan main accessory. I’m not yet sure if it will be similar or different, but this was a good trial run. You can sort of see it below next to one of said Kenner style figures, which itself is made from parts that didn’t really work for the other figures I had. The resin in some of these limbs came out too squishy to really be used, but can’t let it go to waste, now, can we? I’m still going to put this one together and paint it.
Below, you can see how Aurora’s torso comes out of the mold. As you can see, there’s a fair amount of clean up needed.
Some of the figures made so far, prior to priming and painting. I’ve made two others since and am working on a third.
Some shrunk down rocket packs done with bits of resin left over casting the limbs to the figures (more to come shortly). This technique uses mineral spirits added to the mold mixture. The mineral spirits slowly evaporates away, shrinking the mold. You can see here how much these Rocketeer packs shrunk down compared to the original one made for a Reaction Rocketeer figure.
Since there’s always leftovers, I often pour them into other small molds, too. The hoverboard above is actually the one of the left, minus the paintjob, front console, and the peg for the figure to stand on. The synthesizer on the right is the same one I used to make one for Logan to play on – the first custom action figure I did – and used to make crayons and recycled plastic keyboards:
I added QR codes on the back of these miniatures for songs from The Thirteenth Hour soundtrack and figured they could be kind of like 3D business cards.
For example, I thought they’d be fund additions to a Thirteenth Hour mask combo package I recently put on Etsy. This fall, it became really hard to find good quality masks for our kids as they were going back to school. There are still long wait times for some of the companies we like best, so I thought, why not try to find an alternative? I eventually settled on the triple layer masks available for printing on by the company Flashbay. They were one of the few companies I found that were transparent about their third party safety data (Junior: https://static.flashbay.com/images/certificates/Junior_REACH.pdf?v=1617870020, Adult: https://static.flashbay.com/images/certificates/Sky_Performance.pdf?v=1603078812), which is nice. I was impressed by how well these masks performed on the filtration tests, even after repeat washings. Also, I really liked how both the ears and nose piece could be adjusted for a good fit.
This week, we’re discussing new toymaking updates, reading the next section of the Howard the Duck novelization, and watching and discussing the second part of the 1994 film, The Crow.
Toymaking stuff first: I have a handful of Logan and Aurora 5 POA Kenner-style action figures that are ready for priming, painting, and final touches:
We are are reading the next section of the Howard the Duck from the movie novelization.
Then, we are wrapping up talking about The Crow:
As mentioned in the episode, the score by Graeme Revell provides a haunting backdrop to the film that sets the tone perfectly. You can find both the regular and deluxe editions on Youtube:
Although I believe there was a Crow skin you could download for the game Max Payne (which was very Crow-like in many ways), there were not video games made of the first film. There was one made of the sequel, though. Check out the hilarious AVGN review.
If you want to stay within the world of the first film, checking out the TV series, which is different from the film in some ways, is not a bad way to do it. The first episode is basically a retelling of the film with some adaptations to make the series continue.
Welcome to the second part of the Halloween editions of The Thirteenth Hour podcast! This week, we’re discussing a few toymaking updates, reading the next section of the Howard the Duck novelization, and watching and discussing the first part of the 1994 film, The Crow.
Toymaking stuff first: I have some working prototypes of the Logan and Aurora 5 POA action figures:
Another slightly related thing and a preview of coming attractions (hopefully helpful for this winter) is there will be some Thirteenth Hour masks for kids and adults coming soon:
We are are reading the next section of the Howard the Duck from the movie novelization.
Then, we are wrapping up Halloween by starting a two part segment on The Crow:
There is some great free running that happens on the rooftops in this film, as evidenced by this scene.
This is one of my favorite solos of all time and such a great example of how you can use music to convey heartfelt emotions without resorting to verbal exposition. This solo was inspiration for one of the tracks on a upcoming Thirteenth Hour soundtrack, entitled “Mourn of the Midnight Phoenix.”
The score done by Graeme Revell is great. One of my favorite tracks on the score is this one.
The Thirteenth Hour Podcast #34 and Like a Hood Ornament #40: Toymaking Updates, Watching the Rocketeer Cartoon Episode 19, and Reading The Howard the Duck Movie Novelization Part 11
Welcome to the first part of the Halloween editions of The Thirteenth Hour podcast! This week, we’re discussing a few toymaking updates, reading the next section of the Howard the Duck novelization, and watching the Halloween episodes from The Rocketeer cartoon.
Toymaking stuff first: with the spare resin that comes from making other things, I’ve been saving a bit for these little helmets to become (once finished) to Rocketeer helmets for the Lego Rocketeer minifigures to be donated to charity auctions:
There’s always resin left over after a project, so I generally pour it off into another easy to use mold, like this one. Some of those projects:
The Beverly minifgures – still got to clean up the flashing along the seam lines and touch up a bunch of other parts (basically consisting of lots of filing, sanding, etc. edges and other parts, perhaps also strengthening the guitar necks). Then they will be ready for painting (at least the non glow in the dark ones).
Lastly, it’s rough, but I finally have a prototype cast Logan made from flexible Smooth-On Smooth Cast 45 D resin for the limbs and head and Smooth-On Smooth Cast 300 resin for the torso. I might try to make one that is all made of 45 D since I might be able to make it translucent, which would be fun. Now, it’s just a matter of fine tuning the casting process to make sure the limbs can reliably fit inside the torso – which they did on the initial non-cast prototype but somewhere along the lines, something got lost in translation after casting and tolerances that were tight are no longer.
We’re also watching the next episode of the Rocketeer cartoon (number 19) … the Halloween episode! Some screenshots:
You can see Kit’s dressed up like a WW1 pilot for Halloween, making her look just like Cliff in the beginning of the film or in various pages of the comic by Dave Stevens.
We are are reading the next section of the Howard the Duck from the movie novelization.
The author added another humorous aside calling back to our episodes on The Wizard of Loneliness, where “Lord, love a duck” was a frequent utterance.
The Thirteenth Hour Podcast #323 and Like a Hood Ornament #39: Toymaking Updates, Watching the Rocketeer Cartoon Episode 18, and Reading The Howard the Duck Movie Novelization Part 10
This past week, I have been waiting for some new resin to arrive for the Logan and Aurora Kenner style figures. In the meantime, I have been working on these Lego Rocketeer minifigures to be donated to charity auctions. Here’s what I’ve got so far:
The packs and helmets are being resin cast. As I mentioned in the episode, I think I will use magnets to attach the rocketpacks, at least the ones not intended for kids. (Rare earth magnets and small children are a bad combo).
We’re also watching the next episode of the Rocketeer cartoon (number 18) … Some screenshots:
… and readung the next section of the Howard the Duck from the movie novelization.
The author added this especially humorous segment:
The Thirteenth Hour Podcast #322 and Like a Hood Ornament #38: Toymaking Updates, Watching the Rocketeer Cartoon Episode 17, and Reading The Howard the Duck Movie Novelization Part 9
This past week, I made a mold for the Logan and Aurora Kenner style figures. There will need to be another one, since the torso halves are being made with different resin.
This past week, I have finally got around to making the mold for the Beverly Switzler minifigure. I made a two part mold that attempted to protect what I figured would be a delicate area of the figure (the neck of the guitar) but the realized after the facts that certain other delicate parts, like the guitar strap, would probably get caught in the mold and not make it out successfully. So that part I may have to add later. Here are some steps involved:
Add a clay backing to make one half…
Then preparing for the second layer, including adding a bunch of air vents …
And now, speaking of which, back to the duck! The zaniness continues in this eighth reading of the movie novelization Ellis Weiner, based on the screenplay by Willard Huyck and Gloria Katz. This is the infamous section of the story where Howard and Beverly almost hook up … or do they? 🙂 It’s handled here in the novel much less awkwardly than in the film, I must say!
Lastly, all proceeds to The Thirteenth Hour Studio on Etsy over Sept will be donated to the Red Cross (RedCross.org) for Hurricane Ida Relief. Check the link below to support those affected, still in the midst of the pandemic, with 80s retro art (music-books-toys). Your purchases help those in need get back on their feet!
This past week, I’ve made some toy progress: 1.) on my Alumilite resin experiment – just finished this translucent metallic blue Rocketeer (Pledge Floor Polish really helps to bring back the sheen after sanding), as well as 2.) with the 5 POA Kenner-style Logan and Aurora from The Thirteenth Hour. Logan is basically ready to go. Aurora needs a few more details but is about 80% complete. Once these guys are done, it will be time for making the molds and casting the pieces. The exciting part will be assembling the pieces to see how they all fit together.
Also, I want to thank all of you who took the time to write in and leave reviews on Apple Podcasts. The process of doing so should be easier than it actually is, especially for all the non-Apple users. Don’t worry if you tried but it didn’t work. Just posting it on social media and tagging me works great, too, and frankly, is probably a hell of lot easier. Game developer Antonio Scacchetti, who left one of the reviews, was on the show twice before (see episode 123 and the 2 parter: 252 & 252). Check out Dev9k for more info on their projects!
And now, speaking of which, back to the duck! The zaniness continues in this sixth reading of the movie novelization Ellis Weiner, based on the screenplay by Willard Huyck and Gloria Katz. This is the section of the story where Howard rage quits, gets in a bar fight, and reunites with Beverly.
This week’s bit of 80s trivia comes in the form of inventor and entrepreneur Sir Clive Sinclair, who sadly passed away recently. He was instrumental in developing the pocket calucator and personal computer for the masses. He also happened to shar a last name with a certain actor in the 1991 film of The Rocketeer, so I used that as a way to throw in a bit of 80s trivia in the short story, “The Last Rocketeer,” which you can read here. It always seemed to me that Cliff Secord would have liked video games if they’d been invented in his day, so I figured why shouldn’t he get to enjoy them in his golden years? 1983, to be exact.
Lastly, all proceeds to The Thirteenth Hour Studio on Etsy over Sept will be donated to the Red Cross (RedCross.org) for Hurricane Ida Relief. Check the link below to support those affected, still in the midst of the pandemic, with 80s retro art (music-books-toys). Your purchases help those in need get back on their feet!
This past week, I’ve been experimenting with a new clear resin made by the company Alumilite, testing it out with some of my old molds just to get the hang out it. It takes a lot longer to cure and is a bit more fiddly / messy than the others I’ve used, but each resin has its own personality, so to speak, and I like the option of being able to make clear or translucent figures, which is what this one can do. Here’s an example of a Rocketeer one I started:
At this point, I have a prototype of the 5 POA Kenner-style Logan from The Thirteenth Hour (I was running low on primer here and just had a bit or blue and silver paint/primer left, leaving him looking like the Tinman from The Wizard of Oz, though that will mostly get sanded down in the finishing process). There is also the start to one for Aurora (made so far from a She-Ra torso and legs – picked because it was one of the few figures like this that came with a skirt – and an Erica (from Red Dawn) head (since she has the great 80s big hair).
Logan here post sculpting, pre priming …
Post priming, pre sanding …
Aurora is kitbashed from two Reaction figures, as mentioned above. I thought they did a really nice job on the head sculpt. Usually these figures look kind of generic, but this one actually looks like the actress (Lea Thompson, who, ironically was Beverly in Howard the Duck). Since Aurora’s personality and hair was modeled in part on Beverly from Howard the Duck, it was a nice coincidence that I could find a head sculpt that worked for this figure. More to come in the coming weeks …
And now, speaking of which, back to the duck! The zaniness continues in this sixth reading of the movie novelization Ellis Weiner, based on the screenplay by Willard Huyck and Gloria Katz. This is the section of the story where Howard storms out of the museum, strikes out on his own, and tries to get a job.
Totally random, but check out this Kool-Aid ad / pamphlet from probably the late 80s or early 90s. My mother in law saved it, and it made its way to our house. I thought, “I must share these gems with the world.” And here it is … enjoy! And if anyone has tried a blue Kool Aid – Jello smoothie, I would love to know what you thought.
Lastly, all proceeds to The Thirteenth Hour Studio on Etsy over Sept will be donated to the Red Cross (RedCross.org) for Hurricane Ida Relief. Check the link below to support those affected, still in the midst of the pandemic, with 80s retro art (music-books-toys). Your purchases help those in need get back on their feet!
The Thirteenth Hour Podcast #317 and Like a Hood Ornament 37: Reading The Howard the Duck Movie Novelization Part 5, Rocketeer News, and Toymaking Updates
Some interesting news this week. The Rocketeer is supposedly getting a sequel! Now, I am not holding my breath, since there have been sequel rumors for years, and so far, they have all died on the vine. But it is exciting, nonetheless. Even if nothing comes of it, if it generates some interest in Dave Steven’s original comics and the 1991 film for a new generation, I view that as a win.
One thing that does seem more tangible, since it is slated for a release next month, is a beautiful Rockeeter board game. Now, I gotta be honest, board games have never really been my thing. Half the time, when I read the instructions, I go, “What? I don’t understand what the hell you are supposed to do. Who wrote these things?” Also, maybe once my kids are older and we can all play them together, it will be a different story, but most of the ones more complicated that Candy Landy require a level of concentration pretty much making them a no-go for the little ones. But … that is not to say that will always be the case! Plus, game or no game, I would buy this one for the little miniature Rocketeer figurines alone (which I was thinking of trying to make a few months ago – this saves me the trouble)! I will be looking forward to this one this fall for sure.
Speaking of The Rocketeer, I am using a Reaction Rocketeer figure as the base of the body for a 5 POA Kenner-style figure of Logan from The Thirteenth Hour. The head will be modified from a figure of the Charlie Sheen character from Red Dawn. Just need to do a few more touch ups and then make it all go together smoothly. More to come shortly.
Here are a few pictures of the Beverly minifigure I have been working on for the past few months: Just about done, I think. Just a few touch ups here and there.
And now, speaking of which, back to the duck!
This is the section in the story where Howard meets Phil (a young Tim Robbins). There are some really funny asides the author, Ellis Weiner, added for this segment:
Lastly, all proceeds to The Thirteenth Hour Studio on Etsy over Sept will be donated to the Red Cross (RedCross.org) for Hurricane Ida Relief. Check the link below to support those affected, still in the midst of the pandemic, with 80s retro art (music-books-toys).
This week, we’re again taking a short break from the 30th anniversary of The Rocketeer by celebrating the 35th anniversary of my another of my favorite films, Howard the Duck. The zaniness continues in the movie novelization of Howard the Duck by Ellis Weiner, based on the screenplay by Willard Huyck and Gloria Katz, though with a number of humorous and satirical additions that were unique to the novelization. Some of those are also found in the three part comic adaptation that came out about the same time as the film and novel. A few screenshots:
As mentioned in previous weeks, there is a Howard the Duck documentary, Howard the Doc, currently being created with interviews from some of the original writers / cast / crew. I do believe it is the only one that has ever been attempted for this first of all Marvel movies.
It is in the final stages of production. Their team needs some love / support / bucks to help complete the project, and you can support them on Indiegogo. Some crowdfunding platforms don’t result in any funding going to the creators if the final goal is not met, but in this case, the filmmakers will get it every penny that you contribute even if the final target is not met. If you have love for the 1986 film, comic, the original cast/crew, or 80s movies in general, please consider taking a look at the campaign, sharing on your social media, or contributing. Hopefully, then we can all see the final product!
Some screenshots of the production with Ed Gale (who was inside Howard), Jeffrey Jones (a.k.a. the principal who get booted in the face in Ferris Bueller’s Day Off), and Lea Thompson.
The minifigure that I am making of Beverly, along with a portrait of Howard, is now a perk if you contribute at the $125 level. Check out the fundraiser above; I believe it is ending on 8/30, so spread the word!
This week, we’re again taking a short break from the 30th anniversary of The Rocketeer by celebrating the 35th anniversary of my another of my favorite films, Howard the Duck. The zaniness continues in the movie novelization of Howard the Duck by Ellis Weiner, based on the screenplay by Willard Huyck and Gloria Katz, though with a number of humorous and satirical additions that were unique to the novelization. So far, I’m liking the novel version of Howard more than the movie version (some screenshots below from the film of this segment).
In this part of the chapter, we learn a little more about Beverly Switzler, the frontswoman of Cherry Bomb, an all female band essentially created for the film. Howard, sleeping in a garbage can, meets Beverly, who has just played a disappointing gig and gets accosted by some overly intrusive “fans.” He fakes some “quack fu” and scares the things away, though as in the film, Bev hardly sits passively at the sidelines.
I found some drawings I believe done by Joe Tompkins, the costume designer for the film. There’s a collection of sketches he did that you can see from the film for Beverly and Howard (click below for more info):
Speaking of the film, there is a Howard the Duck documentary, Howard the Doc, currently being created with interviews from some of the original writers / cast / crew. I do believe it is the only one that has ever been attempted for this first of all Marvel movies.
It is in the final stages of production. Their team needs some love / support / bucks to help complete the project, and you can support them on Indiegogo. Some crowdfunding platforms don’t result in any funding going to the creators if the final goal is not met, but in this case, the filmmakers will get it every penny that you contribute even if the final target is not met. If you have love for the 1986 film, comic, the original cast/crew, or 80s movies in general, please consider taking a look at the campaign, sharing on your social media, or contributing. Hopefully, then we can all see the final product!
Some screenshots of the production with Ed Gale (who was inside Howard), Jeffrey Jones (a.k.a. the principal who get booted in the face in Ferris Bueller’s Day Off), and Lea Thompson.
This week, we’re again taking a short break from the 30th anniversary of The Rocketeer by celebrating the 35th anniversary of my another of my favorite films, Howard the Duck. The zaniness continues in the movie novelization of Howard the Duck by Ellis Weiner, based on the screenplay by Willard Huyck and Gloria Katz, though with a number of humorous and satirical additions that were unique to the novelization. So far, I’m liking the novel version of Howard more than the movie version.
An example of some of the bits of humor thrown in by author Ellis Weiner that doesn’t make it onto the screen. Sometimes these movie novelizations were kind of phoned in, but so far, this one really goes above and beyond the call of duty.
Here is the section where we meet our heroine, Beverly. There is a little more detail about her and her band mates here than in the film, which is one of the nice things that these movie novelization did when done well.
Speaking of the film, there is a Howard the Duck documentary, Howard the Doc, currently being created with interviews from some of the original writers / cast / crew. I do believe it is the only one that has ever been attempted for this first of all Marvel movies.
It is in the final stages of production. Their team needs some love / support / bucks to help complete the project, and you can support them on Indiegogo. Some crowdfunding platforms don’t result in any funding going to the creators if the final goal is not met, but in this case, the filmmakers will get it every penny that you contribute even if the final target is not met. If you have love for the 1986 film, comic, the original cast/crew, or 80s movies in general, please consider taking a look at the campaign, sharing on your social media, or contributing. Hopefully, then we can all see the final product!
Some screenshots of the production with Ed Gale (who was inside Howard), Jeffrey Jones (a.k.a. the principal who get booted in the face in Ferris Bueller’s Day Off), and Lea Thompson.
This week, we’re taking a short break from the 30th anniversary of The Rocketeer by celebrating the 35th anniversary of my another of my favorite films, Howard the Duck. When I was creating the Aurora character from The Thirteenth Hour, Beverly from the film was one of the influences I used in creating Aurora’s character. Awhile back, I found an old copy of the movie novelization so figured this would be the perfect time to read it on the podcast. It’s based on the screenplay by Willard Huyck and Gloria Katz, so I’m thinking it may give some background info that might help explain some parts of the film. And this intro section does not disappoint – it is totally bonkers!
If you’re a member of the Patreon, check out the exclusive podcast they dropped this past weekend for more on the making of a Beverly minifigure. Will be posting periodic updates as the initial clay sculpt gets finished and the molding / casting process gets underway.
The Thirteenth Hour Podcast #306 and Like a Hood Ornament #33: Watching The Rocketeer Cartoon Episode 14, Celebrating the 30th Anniversary of The Rocketeer (6/21/1991)
The day this episode releases will mark the 30th anniversary of The Rocketeer. In celebration, I have a few special things for this episode, including a few accompanying video segments.
The first is the opening of the Diamond Select version of the Rocketeer figure:
The next segment is annotation of a short part in the film where the Rocketeer is caught in between G-men, gangsters, and Nazi storm troopers, eventually leading to those iconic scenes where he’s taking off by the American flag.
Although he is shown in both the comic (on covers mostly) and in pictures holding a Mauser C96 pistol, he never actually gets to use it in either the film or the original comic (more next week). This clip shows how he obtained it in the film:
This week, I’ll finish a little Rocketeer one screen game made with the app Pixicade. It will be a shooting game, since those are very easy to make the the built in physics engine the app has. Here is a preliminary drawing:
Now onto more family friendly things! Some pictures from the Rocketeer cartoon part of the episode:
Lastly, check out episode 43 of I Used to Like This One for a guest appearance I made on the show to discuss the 1991 film version of The Rocketeer for the 30th anniversary of the film.
Lastly, thanks for all who joined in for the live Facebook concert of Thirteenth Hour music with the custom Logan action figure that happened on 5/30/21. You can replay it here:
Set list:
1.) The Thirteenth Hour Theme*
2.) Empty Hands+
3.) Dragons’ Eyes*
4.) Forever Young (by Alphaville, acoustic guitar cover)
5.) Dreams Go Far*
6.) I Will Remember You (by Amy Grant, acoustic guitar cover)
If you would like to grab a little piece of The Thirteenth Hour, pick up a patch of Logan flying off into the sunset and bask in many of the things we discussed in this episode – silver flying machines, cloudscapes, and the sun setting on another day signifying a hope for a better tomorrow. The patches come with a high quality mp3 download from Once Upon a Dream, the next Thirteenth Hour soundtrack LP.
If you still have a cassette player, take advantage of the following deal and be transported to another world! SALE! While supplies last, grab Long Ago Not So Far Away on cassette! Just $1/tape – last week only! https://ko-fi.com/s/5579db9b27
The hood as been sculpted on …
/pic6361051.jpg)
